Ref. 797
A white matt PP film, 100 µm, with a specific coating for high-speed fast inkjet printing. The synthetic rubber hotmelt adhesive delivers high tack and works on both polar and non-polar surfaces. Service between -20 and +70 °C. Multi-sector: luggage, medical, packaging and food.
Fast inkjet · High tack · Polar and non-polar · Service -20/+70 °C · Luggage · Medical · Packaging
When is this the right material?
The labelling process uses high-speed fast inkjet printing and you need a matt PP with a specific coating that fixes the ink well without smudging or bleeding
The bonding surface may be polar (glass, metal) or non-polar (PE, untreated PP, HDPE) and you need a single adhesive that works on both without having to change material
The application is multi-sector — airline luggage, the medical sector, secondary packaging or food — and in every case it is printed at high speed directly in line
The label must remain stable in both cold-chain and elevated-temperature environments, with the adhesive not failing between -20 and +70 °C
Always run a water-resistance test on the ink with your specific equipment before starting production.
Why synthetic rubber changes the picture
Fast inkjet + an adhesive that bonds to almost any surface
The differential angle of Ref. 797 is the combination of two things that don't usually go together: a matt PP prepared for high-speed fast inkjet printing, and a high-tack synthetic rubber hotmelt adhesive. Conventional acrylic adhesives work well on polar surfaces but struggle with untreated non-polar plastics. The synthetic rubber in this hotmelt solves that: it bonds to glass and metal as well as to PE, PP or HDPE, with no need for corona treatment or a change of material.
The service range is wide: from -20 to +70 °C. That makes it valid for cold-chain labels, temperature-controlled logistics, luggage labelling exposed to changing conditions in an aircraft hold, or packaging lines with moderately hot environments. The adhesive's softening point is around 92 °C, so it is not suitable for processes with sustained intense heat.
Before starting production, a print test is needed with the specific equipment and ink formulation. Water resistance behaviour can vary depending on the fast inkjet system and speed. The material can be stored for up to 12 months in its original packaging, in a cool place at 50-60% relative humidity.
Before specifying
Fast inkjet printing
Water-resistance test mandatory
Always validate with your equipment and ink formulation before starting production — the result can vary depending on the system.
Hotmelt rubber adhesive
45 ±3 g/m² · Softening point ~92 °C
High immediate tack · Not suitable for processes with sustained intense heat above 70 °C in service.
Service range
-20 / +70 °C
Industrial cold through to moderate heat · Multi-sector with no change of material.
Physical properties of the material
| Parameter | Value | Unit | Notes |
|---|---|---|---|
| Matt PP Fast Inkjet Film | 100 ±2 | µm | White matt · Specific coating · Dye and pigment inks |
| Hotmelt rubber adhesive · coat weight | 45 ±3 | g/m² | Synthetic rubber · High tack · Polar and non-polar |
| Adhesive softening point | ~92 | °C | Softening point of the hotmelt · Not for high temperature |
| Application temperature | +5 / +45 | °C | Minimum temperature needed for correct bonding |
| Service range | -20 / +70 | °C | Industrial cold, room temperature and moderate heat |
| Total thickness | 205 ±8 | µm | 100 µm film + adhesive + liner · Total weight 190 ±5 g/m² |
| White glassine liner | 63 | µm | 72 ±4 g/m² · Automatic dispensing |
| Shelf life | 12 | months | Original packaging · Cool place · 50-60% relative humidity |
Synthetic rubber hotmelt adhesive — key performance
Performance against conditions of use
Fast inkjet printing
Specific coating for high speed · Dye and pigment inks · Always test water resistance with your equipment before starting production
Polar and non-polar surfaces
Synthetic rubber hotmelt · Bonds to glass, metal, PE, PP and untreated HDPE · No need for primer or corona treatment
Wide thermal range
-20 / +70 °C in service · Valid for cold chain, hold luggage and packaging with moderate heat
Extreme high temperature
Adhesive softening point ~92 °C · Not suitable for processes with sustained intense heat, autoclaves or heat tunnels
Multilayer composition
How it is built
Do you need to validate this material for your application?
Tell us which fast inkjet system you print with, the bonding surface and the application sector. We will confirm whether Ref. 797 is suitable for your project within 24 hours.
If you need compatibility with a specific non-polar surface, let us know and we will validate the adhesive under your real conditions.
Technical documentation
For more technical details, we have the complete version of the Technical Data Sheet in PDF format.
Download PDF specificationSupply details
Free technical sample
We send it to you before production to validate in your real process.
Response in less than 24 hours
Technical consultation handled by specialists since 1994.
Custom format
Roll, sheet or die-cut according to reference and process.
Delivery throughout Europe
We supply to the entire European Union.
Do you need to validate this material?
Tell us your fast inkjet system, the bonding surface and the sector of use. We will reply within 24 hours.
- Free technical advice with no obligation.
- Response in less than 24 hours.
- Material samples when the project requires it.